Le protocole Panasonic CTRL-M

Document en cours de traduction de l’anglais vers le français par CTV et trouvé sur le site AVIT RESEARCH

Le rédacteur original de ce document est David Meed dmeed@nbnet.nb.ca

======================================================================

Le mardi 25 juin 1996

Ces informations ont été glanées sur plusieurs

sources. Une est une télécopie d’un magazine allemand de

1993. L’autre est une information technique sur le protcole à 5

broches pour le magnétoscope panasonic AG 1960.

nous avons seulement ces quelques pages pas vraiment nettes au format

tif. Si quelqu’un a le temps de convertir les fichiers tif en texte qu’il

nous les envoie à notre adresse de contact.

Le texte prend moins de place que l’image.

Les fichiers tif sont :

AG1960_1.TIF à AG1960_B.TIF : Pages 1 through 11 of a Panasonic

product information bulletin on the AG-1960 5 Pin Protocol. The original

photocopies were faxed to my PC and converted to Huffman compressed TIFF

files.

CTL_MTXT.TIF - a faxed copy of the email from which much

of this text is typed.

CTL_M_G1.TIF - a faxed copy of a page from a German Magazine.

CTL_M_G2.TIF _ a faxed copy of another page from the same

article.

Ils sont réunis en un seul fichier ZIP doc_ctrl_m.zip

qui fait 489 Ko.

Ces informations ont été mises en page en vitesse.

Ne m’incediez pas, laissez moi le temps de peaufiner une version ultérieure.

 

======================================================================

 

 

============================

 

Panasonic 5 pin edit control

 

============================

 Remote Control Jack (2.5 mm)

 ----------------------------

 Tip - negative-going TTL pulse synchronous to

vertical frame at 100

 Hz (PAL)

or 120 Hz (NTSC)

 Ring - +5 on record, frame frequency (25/30Hz

at playback)

 Pull TIP to ground briefly to start recording.

 5 pin Edit jack (11 pin jack is a superset of this)

 ---------------------------------------------------

 Synchronous serial transmission clocked by the

VTR

 1 bit=27 microseconds

 Bits from VTR become valid at the falling edge

of the clock.

 Bits should be sampled at the rising edge of

the clock, VTR does this.

 1 Frame = 7 bytes

 Bytes 1 and 2 are all ones (reserved)

 Byte 3 takes commands to the VTR

 VTR

Commands

 ==========================

 Send

on Byte 3 

EC100 EC200 EC300

 

$00 Stop 

x x x

 

$02 Rewind 

x x x

 

$03 Fast Forward 

x x x

 

$04 Review 

x x x

 

$05 Cue 

x x x

 

$06 Still/pause 

x x x

 

$08 Record 

x x x

 

$09 A-Dub 

x

 

$0A Play 

x x x

 

$0B Reverse Play 

x x

 

$0C Frame Advance 

x x x

 

$0D Reverse Frame Adv. 

x x

 

$0F Slow 

x

 

$2E Slow Up 

x

 

$2F Slow Down 

x

 

$33 Counter Reset 

x x x

 

$94 Direct Search 

x

 

$9D Assemble Insert x 

x x

 

$9E Assemble Record x 

x x

 

$9F Assemble Play 

x x x

 

$A8 Preroll Wait 

x

 

$A9 Assemble A-Dub 

x x

 

$AA Assemble A/V Insert 

x x

 

$AB Rehearsal A-Dub 

x x

 

$AB Rehearsal A/V Insert 

x x  ?? $AC ??

 

$AB Rehearsal Insert 

x x  ?? $AD ??

 

$AB Rehearsal Record 

x x  ?? $AE ??

 

$AF Frame Requeset 

x x

 

$EF NOP (Connect) 

x

 

$FE NOP 

x x

 ==========================

 Byte 4...7 are data from the VCR

 4 - state of drive

mechanism

 VTR Modes

 ==========================

 Recieve

Byte 4, Low 4 bits

 

$0 Stop

 

$1 Eject

 

$2 Rewind

 

$3 Fast Forward

 

$4 Review

 

$5 Cue

 

$6 Slow

 

$7 Power Off

 

$8 Play

 

$9 Still/Pause

 

$A Record

 

$B Record Pause

 

$C Audio Dub

 

$D Audio Dub Pause

 

$E Insert

 

$F Insert Pause

 ==========================

 Byte 5 - unit of time/hi digit of tape position

 Byte 5 

Byte 6, 7

 ============================================================

 %0000xxxx - Tape counter 

Count Hi 2 digits, Lo 2 digits

 %0101xxxx - Memory counter 

Count Hi 2 digits, Lo 2 digits

 %x01xnnnn - Hour * 1 digit 

Minutes, Seconds

 %x11xnnnn - Minute * 1 digit 

Seconds, Frames

 ============================================================

 Series VW-EC300 Cameras

 ============================================================

 Byte 5 bit 4 (& %00010000)

- counter sign, 1=negative

 Byte 5 bit 7 (& %10000000)

- reverse play mode, 1=reverse

 ============================================================

 

 

Timing diagrams (ASCII Art - use a monospaced font to view !)

===================================================================

 _ 

_ _

 _/ \____/ \ /\ 

_/ \____/ \ /\

 / 

\/ \ / 

\/ \

 ------------------------ ---------------------- 

Video signal

 

-  

- 

 <--------ca 20ms (PAL)----> (16.6ms NTSC)

 <ca 4ms>

 ___________________ 


 Synchronized to

 |||||||| 

|||||||| 

video signal

 | \

 | \

 | 

\

 | 

\

 | 

\

 min 600 us <---> between bytes

 216 us<-> 

each byte

 _ ___ ___ ___ ___ ___ ___ ___ ______ 

Clock

 |_| |_| |_| |_| |_| |_| |_| |_|

 _1___2___3___4___5___6___7___8______ 

Data Byte

 |_| |_| |_| |_| |_| |_| |_| |_|

 

/ \

 1 & 2 Reserved \

 /3 - Data

to VCR

 / 

4, 5, 6, 7, 8 - Data from VCR

 / 

\

 / 

\

 / 

\

 _ _ _ _ 

_ _ _ _ ________

 |_| |_| |_| |_| |_| |_| |_| |_| 

Clock

 __ _________ _____ _____ 


 |___| |___| 

|___| |___| Data

(Bits)

 0 1 1 

0 1 0 1 0

 MSB 

LSB

 <---> 27us

 

__

 Bits become valid with clock falling edge 

|__

 

__

 and are sampled

at clock rising edge __|

===================================================================

 

Panasonic 5 pin and 11 pin connector

===================================================================

 

 

(key) 

(Key)

 

|

 

11 v 6

 

5 1 

5 1

 

4 2 

10 4 2 7

 

3

 

9 8

 

 

(only 11 pin)

 Pin 1 - CR power Switch 

Pin 6 - Audio out L

 Pin 2 - Serial Data 

Pin 7 - Audio Gnd

 Pin 3 - Gnd 

Pin 8 - Audio out R

 Pin 4 - Serial Clock 

Pin 9 - Chroma

 Pin 5 - +5 regulated 

Pin 10 - Video Gnd

 

Pin 11 - Luminance

===================================================================